"Enotec" markasına ait modeller;
OXITEC Economy sintered metal filter disc Length: 500 mm The filter head is made of corrosion-resistant stainless steel 1.4571 (316ss) and has a sintered metal filter. The basic probe has a filter head with a length of approx. 500 mm, whereby the probe reaches this immersion depth. Larger immersion depths are through correspondingly longer filter heads achieved. The filter head is located in the flue gas duct at the probe tip above the ZrO2 sensor. It is a diffusion filter, even at high dust loads not polluted. For checking the measuring accuracy and at Calibration of the OXITEC-O2 analyzer system is done with air or a any other test gas, with known O2 concentration, the filter volume rinsed and test gas instead of flue gas is measured.
Kes-10003000

Enotec
OXITEC Economy sintered metal filter disc Length: 500 mm The filter head is made of corrosion-resistant stainless steel 1.4571 (316ss) and has a sintered metal filter. The basic probe has a filter head with a length of approx. 500 mm, whereby the probe reaches this immersion depth. Larger immersion depths are through correspondingly longer filter heads achieved. The filter head is located in the flue gas duct at the probe tip above the ZrO2 sensor. It is a diffusion filter, even at high dust loads not polluted. For checking the measuring accuracy and at Calibration of the OXITEC-O2 analyzer system is done with air or a any other test gas, with known O2 concentration, the filter volume rinsed and test gas instead of flue gas is measured.
OXITEC Economy InSitu O2 Probe 1.4301 / 1.4307 / 1.4571, flange: DN65 PN6 probe Probe model: KES-1000 (basic unit without filter head) Immersion depth: 300 mm ** (other lengths see order code) Filter unit: sintered metal 20 μm ** Degree of protection plug: IP20 (others on request) Probe material: 1.4571 / 1.4301 Max. Flue gas temperature: 400 ° C Ambient temperature probe: -40 ° C to +80 ° C Flue gas pressure: ± 50 mbar Flow rate: 0-50 m / sec Flange: similar to DN65 PN6 O 2 sensor Response time: approx. 0.5 seconds T-90 time: approx. 5.0 seconds (horizontal installation position) Measuring accuracy: better than 0.2% of the measured value Resolution: better 1 ppm O2 Measuring principle: zirconium oxide Sensor temperature: 800 ° C
Kes-10000000

Enotec
OXITEC Economy InSitu O2 Probe 1.4301 / 1.4307 / 1.4571, flange: DN65 PN6 probe Probe model: KES-1000 (basic unit without filter head) Immersion depth: 300 mm ** (other lengths see order code) Filter unit: sintered metal 20 μm ** Degree of protection plug: IP20 (others on request) Probe material: 1.4571 / 1.4301 Max. Flue gas temperature: 400 ° C Ambient temperature probe: -40 ° C to +80 ° C Flue gas pressure: ± 50 mbar Flow rate: 0-50 m / sec Flange: similar to DN65 PN6 O 2 sensor Response time: approx. 0.5 seconds T-90 time: approx. 5.0 seconds (horizontal installation position) Measuring accuracy: better than 0.2% of the measured value Resolution: better 1 ppm O2 Measuring principle: zirconium oxide Sensor temperature: 800 ° C
PROBE 6FT 115V
Kes-2002

Enotec
PROBE 6FT 115V
PROBE 3FT 115V
Kes-2003

Enotec
PROBE 3FT 115V
GAS ANALYZER SYSTEM FOR O2
Oxitec-5000

Enotec
GAS ANALYZER SYSTEM FOR O2
(PROBE:KES-2002Q82)
SME-5321901Q

Enotec
(PROBE:KES-2002Q82)
ECO-1100114E-H2

Enotec
ECO-10002110

Enotec
Z02-6001EX

Enotec
SMF-200X

Enotec
SME-53210010

Enotec
SIK-5001EX2T

Enotec
SIK-2002-R

Enotec
SIK-2002

Enotec
SIK-2001

Enotec
SIK-132X

Enotec
PROBE, O2, 18IN

Enotec
OXITEC KES-1000

Enotec
OXITEC 5000 ECO

Enotec
OXITEC 5000

Enotec